For Sale GSP rifle BARREL & Stock
Posted: Thu Mar 21, 2024 1:21 pm
Will fit most GSP, other than the earliest models that used a smaller bore diameter for the barrel.
One of the stock and barrel combinations will fit and can be used with most older GSP framesthat use the side retaining machine screws at the upper part of the grip area.
Is this a worthwhile GSP add-on?
The resultant rifle, as a 5-10rd semiauto, provides accuracy approximately equal to most Anschutz M64, and about a third of the M54. Keep in mind, there is variability between individual guns. It is more accurate than essentially any USA-made .22lr semiauto or standard production bolt action .22lr gun. It can be used with diopter or optical sights, due to the long 11mm dovetail at the base of the barrel. The stock in this version is ambidexterous.
At a few hundred dollars, may be worth consideration.
This version is aftermarket from Germany. The barrel is not fluted, no threaded end, and the stock uses thumb-hole grip stock. Full length 11mm v-dovetail at base of barrel for scopes or optical sights, but compatible as-is with iron sights on GSP or OSP. Not bored with progressive twist rate, like the Walther barrels. The barrel length is 21.5, rather than 18 or 16" as in the Walther barrels. Unlike the Walther stocks, a special adapter is not required for standard scope mounts due to the long, 11mm wide dovetail at the base of the barrel.
Only 5 of these stock and barrel units were imported into the US. Total production in Germany probably was limited to a few hundred.
Best used with GSP frames that use a bottom bolt attachment for the grip for most of the available ones. One of the stocks is prepared for use with either the bottom bolt system or the upper machine screw side retainer bolt system. However, if used in the latter manner, the holes for the machine screws are visible.
The stocks are laminated wood layers of medium brown and very dark brown or blackish wood.
Prices vary a little with cosmetic condition of stock and barrel surface.
Please email for images. Please indicate degree of cosmetic perfection desired. Accuracy and bore condition are essentially perfect for all options.
Please avoid using this listing for questions or comments, so that it can be deleted later. Please also indicate contact was via Target Talk so that contributions as appropriate can be sent.
Also can be combined with a GSP or OSP if that is desired. Several combinations available.
No FFL required for shipment of the barrel and stock alone.
All of the above also are for sale locally, and can be tested and compared to various Anschutz, Walther, or other match or competition rifles on site, if desired.
Nikita@alum.MIT.edu.
One of the stock and barrel combinations will fit and can be used with most older GSP framesthat use the side retaining machine screws at the upper part of the grip area.
Is this a worthwhile GSP add-on?
The resultant rifle, as a 5-10rd semiauto, provides accuracy approximately equal to most Anschutz M64, and about a third of the M54. Keep in mind, there is variability between individual guns. It is more accurate than essentially any USA-made .22lr semiauto or standard production bolt action .22lr gun. It can be used with diopter or optical sights, due to the long 11mm dovetail at the base of the barrel. The stock in this version is ambidexterous.
At a few hundred dollars, may be worth consideration.
This version is aftermarket from Germany. The barrel is not fluted, no threaded end, and the stock uses thumb-hole grip stock. Full length 11mm v-dovetail at base of barrel for scopes or optical sights, but compatible as-is with iron sights on GSP or OSP. Not bored with progressive twist rate, like the Walther barrels. The barrel length is 21.5, rather than 18 or 16" as in the Walther barrels. Unlike the Walther stocks, a special adapter is not required for standard scope mounts due to the long, 11mm wide dovetail at the base of the barrel.
Only 5 of these stock and barrel units were imported into the US. Total production in Germany probably was limited to a few hundred.
Best used with GSP frames that use a bottom bolt attachment for the grip for most of the available ones. One of the stocks is prepared for use with either the bottom bolt system or the upper machine screw side retainer bolt system. However, if used in the latter manner, the holes for the machine screws are visible.
The stocks are laminated wood layers of medium brown and very dark brown or blackish wood.
Prices vary a little with cosmetic condition of stock and barrel surface.
Please email for images. Please indicate degree of cosmetic perfection desired. Accuracy and bore condition are essentially perfect for all options.
Please avoid using this listing for questions or comments, so that it can be deleted later. Please also indicate contact was via Target Talk so that contributions as appropriate can be sent.
Also can be combined with a GSP or OSP if that is desired. Several combinations available.
No FFL required for shipment of the barrel and stock alone.
All of the above also are for sale locally, and can be tested and compared to various Anschutz, Walther, or other match or competition rifles on site, if desired.
Nikita@alum.MIT.edu.