TargetTalk

I can make one for you, please PM me if you are interested.

For the record, we are not strictly NRA, we're also CMP :) But since there are very few athletes participating in the International competitions these days, it's hard to justify all the expenses and additional paperwork required to run USAS PTO.

Hm, was it Colo Springs or Perry WAG location? In Colorado Springs they had some very calming medieval lute music, but on day 1 and 2 of the matches nothing but classic rock. I was happy for the juniors, it's their only opportunity to listen to good music instead of their usual gangsta rap, but my s...

Welcome to our beautiful sport! You will find it very addicting, I promise :) Here are some of my thoughts regarding your questions, but take it with a grain of salt, at the end of the day you just do what works for you. - Expectations - NONE whatsoever! Every time I think to myself before the match...

Here's a little trick that works for me. Instead of applying the putty directly to the grip, I first cover the area that I'm going to build up with a thin masking tape, and then apply the putty to the tape. It holds pretty well, doesn't move at all, but is easy to remove and leave the grip in its pr...

I just helped an athlete with this at Camp Perry. Once you take the grip off and watch the pieces move, it is quite clear which screw to turn (#2, CW). Note the terminology in the manual may be different than what you are used to. Bob, actually it was me, I appreciate your help but unfortunately I'...

I got a brand new LP500 Expert with mechanical trigger and one issue that I immediately noticed is that it has a significant over travel out of the box. On my LP400 there's a screw that controls it and I found the same screw on LP500, but - it looks like when the shot is released, the whole trigger ...

We paid about $930 USD per unit but the shipping to US was obviously very expensive. We ended up with about $6k total for 5 targets, not including computers, stands and power supply units.

What we got is the InBand Air: https://inband.fi/?page_id=116 They work great most of the time, there are still some quirks and wrinkles, mostly due to the fact that the software could use some improvements, plus it runs on cheap Windows tables - and we all know how "great" Windows is. But...

Actually Pardini DOES recommend applying a very small amount of moly grease to the hammer/sear surfaces. See here: https://www.pardiniguns.com/store/produ ... cts_id=929

There's also video on Youtube: https://www.youtube.com/watch?v=aR1nD387EhA

Again, sorry about it, if everyone here agrees that this post crosses the line, then, moderators, please remove it. I didn't mean to offend or upset anyone here.

First of all, I apologize if this is off topic or inappropriate here. I promise I will do it only this one time. Many of you here and on the Bullseye forum know me in person, so you know this is not a scam or phishing. I started a fundraiser on GoFundMe to raise some money for my old friend and form...

Folks, I know Derrick in person and vouch for him, he's a very talented machinist and smith, and I saw that shroud he made for one of our club members, it looks awesome and much much better than the factory plastic fantastic. One added benefit is that the barrel now can be removed if needed, and als...

So it seems, but with the factory grip I can tighten it all the way and it doesn't cause any problems. Does Rink grip come with another set of hardware? How do other people solve this problem (or am I the only one who has it?)

Thanks, folks this is resolved, I just printed a new cover on my 3d printer :) Magic! Now I have another problem, the grip is attached by two screws, one in the middle and one at the top. So the top one doesn't go all the way in, if I start tightening it, at some point the gun locks up the pellet ga...

I was recently going through the piles of junk in my garage and found almost perfect Rink grip for Morini 162. I installed it on my gun and it fits like a glove, but the battery compartment cover won't fit. The opening on the Rink grip is rectangular with screw hole in the middle of the short edge, ...

We decided to give our humble indoor range at the PRGC some overhaul and I'm looking to replace those old ugly looking benches with something more suitable. Now I'm just looking for ideas and inspirations, and possibly some plans, drawings, instructions, wondering if you guys can share some :)

The expiration date on my Morini cylinders is 2021 (wow, time flies). I know the expired cylinders will make my gun illegal for official competitions, but I'm trying to understand if this is just a precaution or is there really a safety issues there? In other words, should I toss out my cylinders an...

Yes, I do use the lube on all my cylinders and adapters. The O ring looks normal. I guess I'll just need to get another cylinder, this one expires in January 2021 anyway...

I'm having a strange problem with one of my LP400 air cylinders. It won't charge when I screw it onto the adapter and the air tank. My other cylinder works just fine with the same tank and the same adapter. When I screw the adapter onto the cylinder, I hear the air coming out, so it seems like the a...